1 Version1.7
104.5 Rigging the xtureThe installation of the xture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour withou
11Truss installation1.Bolt each clamp (1) to the omega holder (3) with M12 bolt and lock nut through the hole in the holder.2.Fasten the omega holder
124.6 DMX-512 connectionThe xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel.Only
134.7 Ethernet connectionThe xtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control soft-ware running on
14Ethernet / DMX operationOptions “Art2DMX” has to be selected from the “Ethernet Mode” menu on the rst xture (connected to the Ethernet) in the xt
155. Remotely controllable functionsLampThe Robin 300ESpot is to be operated with a Philips MSR Gold 300/2 MiniFastFit lamp.Note: It is also important
166. Control menu mapDefault settings=Bold printTab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Addressing Settings DMX Address 001-255 Ether
17Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Ambient TemperaturesBase TemperaturesPersonality User Mode User A Settings User B Settings
18Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Stand -Alone Test Sequences Dynamic Mode Static Mode Pan 0-255Tilt 0-255Zoom 0-255Focus 0
197. Control menu The Robin 300ESpot Light is equipped with the QVGA Robe touch screen with battery backup which allows to set the xture´s behaviour
2Table of contents1. Safety instructions ... 32.
20Touch any part of the screen or press the [ENTER/Display On] button to display the initial screen with the cur-rent stored DMX address: Touch the gr
217.2 Tab "Information"Fixture Times - The menu provides readouts of xture and lamp operation hours. Power On Time Hours - Select this m
22 Clean the lters and reset this menu item (by touching the text box next to the item "Elapsed Time"). DMX Values - The men
23 User B Settings - the function recalls the user B settings. User C Settings - the function recalls the user C settings.DMX Preset - Use the m
24Magenta Correction - You can choose betwen deep tone of the magenta colour lter (On) or pale tone of the magenta colour lter (Off).Date & Time
25 Edit Program 1 - The option allows to edit user program No.1. Edit Program 2 - The option allows to edit user program No.2. Edit Program 3 -
26 Yellow - yellow ags Focus - a focus module CTO - CTO ags HotSpot- a ne movement of reector Static Gobo - a static gobo wheel
27 Disconnect the xture from the other xtures in a DMX chain. Turn both the computer and the xture on. Make sure the lamp is switched off (only
28SUPPORTED_PARAMETERS *SOFTWARE_VERSION_LABEL *DMX_START_ADDRESS * *IDENTIFY_DEVICE * *DEVICE_MODEL_DESCRIPTION *MANUFACTURER_LABEL *DEVICE_LABEL * *
29Active Lamp Timer This message appears if you try to switch on the lamp within 5 minutes after having switched it off. The xture will store the at
3CAUTION!Keep this device away from rain and moisture!Unplug mains lead before opening the housing!FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL C
30Gobo Carousel Error 1 (Gobo Carousel Error 2 )The messages will appear after the reset of the rotating gobo wheel if this wheel is not located in th
31Iris Motorized iris for different beam diametersFrost lter Separate,variable frost lterZoom Linear motorized zoom: Strobe Strobe
32Total heat dissipation 1426 BTU/h (calculated)Weight (net) 20 kg Dimensions (mm)Accessories - Omega holder (No.99010420)...
(!'(),-(+ : && ;< &&( =0
(!'(),-&,+&1 &&(& 1 &(&((
(!'(),-&(&(( 6( & 3*0 & /!
(!'(),-1 > 1 -#/! $/0 /
(!'(),-&&(& 5 ! &(&( .
42. Operating determinationThis device is a moving head for creating decorative effects and was designed for indoor use only.If the device has been e
53. Fixture exterior view Rear panel of the base:1 - Ethernet input-RJ452 - 3-pin DMX output 3 - 5-pin DMX output 4 - Fuse holder-neutral 5 - Fuse h
64. Installation Fixtures must be installed by a Qualied electrician in accordance with all national and local electrical and const
74.2 Installing the lamp DANGER ! Install the lamp with the device switched off only. Unplug from mains before !To insert the new lamp.1. Disconnec
84.4 Replacing the colour lters and gobos DANGER!Install the colour lters or gobos with the device switched off only.Unplug from mains before!Colour
9Rotating gobos1. Disconnect the xture from mains and allow it to cool. 2. Remove the bottom plastic cover of the head by loosening the 4 quarter-tu
Commentaires sur ces manuels